Toyota CH-R Service Manual: How To Proceed With Troubleshooting

Toyota CH-R Service Manual / Lighting (ext) / Automatic Headlight Beam Level Control System / How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT

HINT:

  • Use the following procedure to troubleshoot the automatic headlight beam level control system.
  • *: Use the Techstream.

PROCEDURE

1.

VEHICLE BROUGHT TO WORKSHOP
NEXT

2.

CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
NEXT

3.

INSPECT BATTERY VOLTAGE

(a) Measure the battery voltage.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

NEXT

4.

INSPECT CAN COMMUNICATION SYSTEM

(a) Use the Techstream to check if the CAN communication system is functioning normally.

Click here

Result

Proceed to

CAN communication system DTCs are not output

A

CAN communication system DTCs are output

B
B

GO TO CAN COMMUNICATION SYSTEM

A

5.

CHECK FOR DTC* (LIGHTING SYSTEM)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main body or HL AutoLeveling / Trouble Codes.

(e) Check for DTCs.

Click here

Body Electrical > Main Body > Trouble Codes Body Electrical > HL AutoLeveling > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B
B

GO TO DIAGNOSTIC TROUBLE CODE CHART (LIGHTING SYSTEM)

A

6.

CHECK FOR DTC* (AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / HL AutoLeveling / Trouble Codes.

(e) Check for DTCs.

Click here

Body Electrical > HL AutoLeveling > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B
B

GO TO DIAGNOSTIC TROUBLE CODE CHART (AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM)

A

7.

PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table

A

Fault is listed in Problem Symptoms Table

B
B

GO TO PROBLEM SYMPTOMS TABLE

A

8.

OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Data List / Active Test

Click here

(b) Terminals of ECU

Click here

(c) Inspection

NEXT

9.

ADJUST, REPAIR OR REPLACE
NEXT

10.

CONFIRMATION TEST
NEXT

END
    System Diagram
    SYSTEM DIAGRAM HEADLIGHT ASSEMBLY ...

    System Description
    SYSTEM DESCRIPTION AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL (a) General The automatic headlight beam level control system ensures forward visibility and prevents dazzling of drivers in oncoming and ...

    Other materials:

    Toyota CH-R Service Manual > Side Airbag Sensor(for Center Pillar): On-vehicle Inspection
    ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to correctly follow the removal and installation procedures for the side airbag sensors. PROCEDURE 1. INSPECT SIDE AIRBAG SENSOR (for Vehicle not Involved in Collision) (a) Perform a diagnostic system check. Click here 2. INS ...

    Toyota CH-R Service Manual > Audio And Visual System(for Radio And Display Type): Sending Malfunction (Navigation to APGS) (U0073,U0100,U0129,U0140,U0155,U0164)
    DESCRIPTION These DTCs are stored when a malfunction occurs in the CAN communication circuit. DTC No. Detection Item DTC Detection Condition Trouble Area U0073 Sending Malfunction (Navigation to APGS) CAN bus connec ...

    Toyota C-HR (AX20) 2023-2026 Owner's Manual

    Toyota CH-R Owners Manual

    Toyota CH-R Service Manual

    © 2017-2026 Copyright www.tochr.net
    0.0139